Weight transmitter 0-5v 0-10v 4-20mA output load cell amplifier
Product List
| Sensorcon Product Lists |
| Strain Gauge | Load Cell | Torque Sensor | Display |
| Linear Strain gauge-AA | Wireless sensor | Slip ring rotary torque sensor | Platform scale display |
| Half bridge strain gauge-BB,HA,GB,FB | Micro load cell | Contactless rotary torque sensor | Truck scale display |
| Shear/torque strain gauge-AB,HA | Single point load cell | Static torque sensor | Controller |
| Full bridge strain gauge-EB, FG,FD | Button load cell | Meters | Junction box |
| Tee Rosettes strain gauge-CA,BA | Shear beam load cell | Coupling | Big screen display |
| Round type strain gauge | S type load cell | | Amplifier |
| Semi-conductor strain gauge | Column load cell | | |
| Bridge type load cell | | |
Size:
Features:
Plastic housing, durable, cost-effective
Housing and wire joints are waterproof design, good sealing
High precision amplifier circuit, good stability
Anti-jamming performance
Wide sensitivity input range
power supply with reverse protection, surge protection, overcurrent
protection
Sensor excitation voltage adjustable
Portable, small size, light weight, easy to install
Suitable for weighing, pull push force, torque, tension and other
strain sensor
Parameter
Mode | PY-V-SP |
Input Signal | mV |
Sensitivity range | Standard: 1MV/V, 1.5MV/V, 2MV/V, 3MV/V
Optional: 0.5MV/V, 4MV/V, 5MV/V ,6MV/V |
Load cell Excitation Voltage | 5~15VDC(Adjustable) |
Operating Temperature | -20~60℃ |
Operating Humidity | <90%RH |
Protection grade | IP65 |
Installation | Housing fixing |
Housing material | ABS |
Working Excitation voltage | Standard: 12VDC, Optional: 24VDC |
Output signal | Current:4~20mA, 0~10mA, 0~20mA |
Voltage:0~5V, 0~10V, 1~5V, ±5V, ±10V |
Please notify us which output you want when place order
Customized output for voltage output is supported |
Accuracy | Current output type ≥ 0.05%F.S |
Voltage output type ≥ 0.1%F.S |
Load cell connection | At most 4 units of load cell in 350 ohm |
Connection:
Wire definition |
INPUT | E+ | S+ | S- | GND | GNDD |
Load cell Input | Load cell Exc + | Load cell Signal+ | Load cell Signal- | Load cell Exc - | Shield |
OUTPUT | 24V | Out | GND | GNDD | |
Transmitter output | Transmitter Exc+ | Transmitter Signal output | Transmitter Exc-(0V) | Shield | |
VR | Zero | Span |
Sensor bridge voltage adjustment potentiometer | ZERO C potentiometer | Full-scale control point potentiometer |
I Zero-Current type, V Zero-Voltage type | I Span-Current type, V Span-Voltage type |
Calibration:
1. Excitation voltage regulation
1.1 Transmitter 24V power supply,
a) When output signal is 0-10mA, 0-20mA, 4-20mA, 0-5V, 1-5V and ±
5V,
Excitation voltage is adjusted to 8-10.5V, (load ≤ 500Ω), factory
default setting is 10.1V,
b) When output signal is 0-10V, excitation voltage is adjusted to
11-12VDC, (load ≤ 500Ω), factory default setting is 11V;
1.2 Transmitter 12V power supply
When output signal is 0-10mA, 0-20mA, 4-20mA, 0-5V, 1-5V and ± 5V,
the excitation voltage is adjusted to 6-8.5V, (load ≤ 320Ω),
factory default setting is 8.01V
1.3 User can adjust the "VR" according to actual situation. Adjust
excitation voltage according to the sensor impedance but should not
be higher than the max. Excitation voltage of load cell otherwise
it will cause damage to the sensor or the sensor will not work
properly.
2. Zero adjustment
First leave the system under no-load state, adjust the "ZERO"
potentiometer to adjust the zero deviation.
Till the indication is to zero.
3. Gain adjustment
Add certain weight to the system, (recommend 60% to 100% full
scale), Calculate output value based on the ratio of added weight
and the max. measuring value. Adjust the "SPAN" potentiometer till
the indicator is to Load ratio indication
4. Re-examination
leave the system under no-load state, measure zero output; add
certain weight, measure the output again and see whether it is in
line with the expected gain. If not, please repeat steps 2, 3
Note: After the adjustment is done, fix the end of the
potentiometer with a sealant or glue to prevent any changing of
potentiometer’s resistance from vibration
Terms and Conditions
1, in strict accordance with the definition of wiring, with
particular attention to distinguish between the sensor and the
output side, the wrong wiring may cause no output or damage.
2, Except the potentiometer, all other electronic components should
not have any change.
3, the device should be installed to the place without vibration
impact, the installation should be reliable, beware of bumps and no
strong corrosive gas around
Company Information
Sensor and Control Co., Ltd. was founded in 2006, mainly engaged in
Torque Sensor, Load Cell, Pressure Transducer, Strain Gauges and
Weighing Indicators. Since establishment, we insist the guidelines
of "Customer Oriented, Quality Focused, Professional Service "All
products we supply are environment friendly and has passed RoHS
test.
Sensorcon, in accordance with the principle of the introduction of
advanced professional ultrasonic gas cleaning, clean Room patches,
automatic temperature compensation and detection, high and low
temperature testing and thermal experiments, laser welding and
printing, CAD design, manufacturing and testing sensor test
equipment and production technology ,manufacture all varieties of
sensors, high precision, stable performance and also has
antiseptic, waterproof, anti-explosion, anti-lightning, etc favored
deeply by users.
